Working on my day off

November 14, 2016 / Matt Talley / Leave a comment

The house remodel seems to never end… I will be so glad to just be and live in our space at some point. We are close, but there are still details left undone – enough that I am trying to concentrate on one room at a time. My plan is to get each done in turn and then move on to the next. I wasn’t as successful at that as I wanted to be this weekend as I bounced back and forth between the living room and our bedroom closet, but I did get a ton done.

I installed the upper shelves and corner shelf in the walk-in closet, laminating two layers of 3/4″ plywood for really strong support over a 54″ span and in the unsupported corner. In addition to using copious amount of glue and screws, I attached the butted plywood edges together with wood biscuits – it is always a fine day when I get to crank up the biscuit joiner.

Almost a year ago, I sourced some corner shelves at one of the local architectural salvage places for less than $200 – far cheaper than what it would have taken me to build them. They came out of a 1930-40’s house and were painted Christmas colors, but I knew that they would be perfect for our living room, which was stripped of its built-ins at some point in the last 88 years. They have sat in storage and until this past week when I pulled them out and got some material together to permanently mount them. Stamps-With-Foot helped me set them in place after I built sturdy bases. Each of them cover a wall plug, so I am in the process of re-routing the receptacle using armored cable. I also have to build in an air-return duct under one and that has taken some serious brain power to get right. I will add trim this week and my wife and Mother-in-law will paint them cabinet white this weekend.

While I was at it, I punched out a rubber washer for a pot lid knob. I made the knob a couple years ago out of some scrap cherry firewood after the original plastic one broke. The original washer had corroded, so I made a new one and installed it.

I also took a couple minutes to mount the red glass post topper on the back fence. It was ordered (along with a spare) months ago and have meant to put it on every weekend since. There is always an excuse for why I didn’t, so I marched right out first thing Saturday with a tube of clear silicone and finally just got it done. It is the little victories that keep me going.

Back in Seattle! Let the projects begin!!

November 30, 2015 / Matt Talley / 1 Comment

After two days of flying with a couple of heavily sedated French Bulldogs, we made it back to Seattle just in time for a home cooked Thanksgiving dinner. We are so glad to be back in our little house! The now sober puppies have staked their claim in our yard, we went to a few of our favorite neighborhood shops and *gasp* went shopping at Target on a SUNDAY *second gasp*!! In France, shopping on Sunday is a mythical creature that is spoken of in whispers. We miss Toulouse and our friends there already, but it is nice that things are sooo easy here.

The cold, rain, and ice was here to greet us, so in the interest of keeping Stamps-With-Foot happy, my first duty was to spend about 6 hours raising our hot tub from its long 2-year sleep. I cleaned it out, rinsed it twice, scrubbed it, filled it half way and ran the pumps, drained it, scrummed it all down again and then filled it to the top. They pump and heater fired right up and so far they are no leaks, but I will kaap a watch out for a while yet. It took about 4 hours for the water to go from 47 to 104 degrees and the temp has held steady.

We use BaquaSpa instead of Chlorine, so I loaded the tub up with a shock treatment after the it had come up to temp and had been circulating for 24 hours. I waited a few hours before taking a water sample into the local spa shop for testing. All good: just needed a little Oxidizer and to increase in the calcium. Wife happy – she sat in the tub yesterday for about an hour like a proper Japanese snow monkey.

I also just “happened” to stop in at Second Use and picked up a couple of painted fir corner cabinets that I have been eye-balling from afar. They will go in our living-room and replace the originals that were pulled out years ago by an unthinking previous owner – I can’t not work on the house. My Father-in-law, the Chatty Buddha, was here for Thanksgiving and I roped him into helping me wedge them into my tiny and very full shop. They will sit there until spring. Also thinking about re-installing an ironing board cabinet in the basement and a phone cubby in the upstairs hall. I have a problem…

Hall Tree and Shoe Rack for My Bride

March 4, 2014 / Matt Talley / Leave a comment

Soon after we moved into La Maison du Talley in Seattle, my lovely bride decided that “we” needed a place to hang coats by the front door. I looked a little at coat racks and hall trees in the shops close to the house, but I just couldn’t stomach paying $250-300 for a semi-crappy coat rack that was the wrong color or wood for our house. I had one of those “light bulb” moments and decided to build one for us. Normally, I would have cut the raised panels (I tried to convince Stamps-With-Foot to let me do linen-fold panels) and added a little fancy trip work, but as I was recovering from shoulder surgery (#4), I decided to go with the re-use route. Second Use is a used hardware and reclaimed building material store in Seattle that I frequent and I cruised over for a used fir 6-panel door. Right away, I found the perfect one that set me back a whole $30. While pushing the cart loaded with the door to the front, I found a couple of cast off cabinet doors, a few odd sections of trim, and a bundle of old tongue & groove fir flooring. A plan formed in my little head…

I cut two feet from the top of the door, then flipped it over. I built a bench and shoe rack from the cabinet doors (raised panels turned in to match the adjacent hutch and the flat panel cabinets in the rest of the house) and attached it to what became the bottom of the door/hall tree. I ringed the top with a flooring plank, tongue down, and then applied some 100 year old left over fir crown molding on the top. The whole thing was sanded down and stained a deep red mahogany and finished off with 3 coats of exterior grade polyurethane.

For the hooks, I sourced a set of coat and helmet hooks from an old Seattle firehouse and small round dog leash hooks from Rejuvenation Hardware. When all was said and done, this was the very first project finished for our home in Seattle, I spent a total of $94, and I wrote a little love note to Stamps-With-Foot on the top of it. My little wife was giddy when I brought it into the house and she raved to friends for weeks about handy and awesome her husband was – made me puff out my chest like a Banty rooster.

If I did this again, the only thing I would change would be to make the shoe shelves movable as they are about 1/4″ too narrow for my running shoes, but perfect for her shoes, which I guess is the most important feature.

$Here is the face frame glued together and clamped. I have a tiny shop and used wax paper to cover the top, so I don\'t want to hear any sh!t about me abusing my table saw!$

From Trash to Basement Built-in

December 19, 2013 / Matt Talley / Leave a comment

I was at one of the architectural salvage places in the SODO area of Seattle one fine summer day 3 years ago and as I was leaving with whatever small treasure I had found (picture Sméagol with his Precious…), I spied a bit of white cabinetry and what looked like a paneled cabinet door in their free/meant-for-the-dumpster pile so I went over and looked to see if I could salvage a bit of whatever it was. The hope was for a door that I could re-purpose or some cool hardware left intact, but I struck gold! Some idiot used a pry-bar and a Sawzall to rip a built-in painted hutch out of a house’s wall during a remodel. It was taken to the salvage shop without a back, one side missing, no top, zero trim left, and with rough recent tool/pry marks all over it. All the shelves were there and the door that I had seen was one of four heavily painted paneled oak doors. I saw some promise and had an exact spot for it, so I piled the wreckage in the back of my truck, roped it down, and sped away before someone could tell me no.

It languished in the basement for part of a year before I tightened the joints, squared it all up, made a back from pine bead-board, built a matching side panel, reinforced the structure and installed it on one of our basement den walls. What used to be the open counter-top space between the original built-in base and top, became storage for boots or snowboards or books (which is what is there now).

I wanted to include Stamp-With-Foot in the project, so I took her with me to pick out some trim. She found a section of fancy scalloped-cut chair rail/case molding that she REALLY liked and I went home and used it in a custom buildup: adding a section of ripped down base molding and a length of popular wood that I ran over with two different router bits to make the top trim.

After getting the piece installed, I realized that I would have a 5″ gap of dead space between the inside top of the cabinet and the finished top, so I rabbited in two shelf lips and built matching hatch covers to provide storage for long or seldom used items in the top of the cabinet. The hatches were finished with brass ring pulls from a local boat supply hardware shop. After some light sanding, Stamps-With-Foot and I put two coats of white cabinet paint on it and I had The Ruminator help me install antiques glass pulls and keyed latches while he was visiting for Christmas. The piece looks like it was built with the house, the top is already filled with mountaineering books, and is a fantastic addition to our basement and home.

Basement Bench and Winter Workshop

February 9, 2013 / Matt Talley / Leave a comment

I have found that my workshop productivity goes way down in the winter/the six months of Seattle rainy season. My garage shop is small and quickly fills with material, lumber, tools, and projects. To add to the handicap of the small size, the lack of heat means that I can’t do any finish-work because of wood humidity, shrinkage/swell, and moisture. I have made do in the unfinished side of our basement for the past three winters, but I am done my wife is done with the mess and clutter and my bitching about an inadequate work area when the weather turns crappy. I need a little bit of dedicated space that I can work on the small stuff year round that doesn’t require power tools and a little bit of assembly/finish space where I can glue and clamp some projects up, a solder station, a spot to reload ammo, work on my bikes, and a clean/dry/warm space to apply stain or a hand-laid finish coat. Add to this my current want of a small metal lathe and mill and I will have the makings of a nice little hobby shop from which to launch my plans for world domination …er, I mean a spot where I can make small parts, solder, or tinker.

Anyway, instead of buying a crazy expensive cabinet bench or making do with a thin metal and partial board Home Depot bench, I have decided to build the sturdiest all-around hobby bench that I can with the funds and material I have available (~$130.00), add some really nice features (aluminum t-track, lots of drawers, removable vises, power, lights, etc…) and make it into a finished piece of furniture that I will be proud to sit at and show off to friends for the next 30+ years. To start the process off, I found a cheap older thick steel framed 6′ workbench at Second Use that I felt would make a bombproof, rock solid base. I sourced a used IKEA cutting-board counter top that I cut down to the appropriate size and then used the trimmed pieces to add thickness and rigidity (I am still going to add some angle iron). I thought about and sketched 3-9 different ways to add some shelving and some organization to the top and was still tossing around options in my head when a realized that an old buffet that my mom had just might work. I took some measurements and looked into reinforcing here and there and realized that not only would it work, but that its style would set the tone and color for the entire bench build.

I decided that the drawers to be added under the bench top needed to be narrow and at least partially match the newly planned top section, so I looked for an older desk or vanity that I could cut apart. I struck out at Goodwill, the Salvation Army, and Craig’s List, but Second Use came through again and hooked me up with exactly what I needed at a decently fair price, well decent after I haggled a bit…

The current state of the build is that the bench top is 2/3 done, the desk is cut apart, the steel legs are up and in place and I am 1/4 of the way done with reinforcing the buffet/top shelving unit. I will update the build as it is completed and share some more pictures.

Spring Cleaning and Garden Prep -2012

March 27, 2012 / Matt Talley / Leave a comment

The sun is out and it looks like spring has finally come to Seattle. I had a full weekend off and was in the country for a change, so it was time to get busy waking the garden and yard up, prepping for planting, take care of some spring cleaning and enjoy a sunny warm day outside. Below is how this past Sunday went for me:

Up and out of the shower by 10:00am
Wife made yummy breakfast with Trader Joe’s Croissants
Coffee made me human
Put on my overalls
Removed extension cords that powered Christmas lights
Started taking down Christmas lights – 2.5 months late
Realized when on top of ladder that I needed long reach tool I made last year
Spent 30 minutes searching…
Remembered that I turned old tool into something else
Muttered dirty words
Spent 10 minutes making new long reach Christmas light removal tool
While on top of ladder, cleaned gutters – 5th time in 12 months…. Stupid Pine tree…
Turned compost
Cleaned and swept shop a little
Took apart one of our winter hot houses.
Planted forgotten bag of tulip/Camila bulbs found in hot house
Shook head and hoped that they will come up
Mulched roses
Feed roses some of the pink Miracle Grow good stuff
Treated roses for Black Spot as preventative measure
Killed some evil dandelions
Laughed manically while committing the deed
Reconnected the garden irrigation system
Wife brought me coffee and a kiss
Mulched the apple and cherry trees
Ran out of mulch
Started to Home Depot and somehow drove past and all the way to Second Use
Found $220+ of oak flooring for $25
Bought oak flooring…
Picked up more mulch at Home Depot and replacement drill for one that was stolen
Unloaded truck
Wife didn’t raise eyebrow at truck full of wood
Got away with unplanned purchase this time…
Trimmed dead shoots from lavender
Mulched around all the lavender
Sweet wife made me lunch
Moved new cabinet from shop into basement
Started to move charcoal grill
Found football sized mass of blue and black mold inside grill
How in the hell does that happen??!?!?!
Gagged more than a little
Muttered more dirty words
Cleaned out mold, scrubbed every surface with bleach solution and wire brush
There were some additional words spoken that start with F
Made HUGE hot fire with oak shop scrap to kill EVERYTHING in grill
Grill now ready for spring
Laid out spot on outside garage wall for new garden tool shed.
Cut stakes for raspberries
Dark outside so went into basement
Sanded kitchen cabinet shelves that are under construction
Put a coat of primer on them
Installed in some drawer slides in what will be new 15″ cabinets beside the stove
Fv#%ing drill battery ran out of juice
My lovely bride made a yummy dinner
Can’t find new charger for new drill
Wrapped last of wife’s birthday gifts
Put finishing coat of clear-coat on Persian table base that I have been redoing
Somehow got finish in my mouth
Spat and tried repeatedly to scrap the turpentine taste off my tongue
Failed
Gave up
Went to bed
Opened book
Not a single word read before I passed completely out.

Driven Outside

Tag: Second Use