Tag: Mallet

GROP update – French Cleats

/ Matt Talley / Leave a comment

Since I live in France, it only makes sense for me to have a shop organization wall that using French Cleats. I have wanted to do it for years, but just never found the time between house and furniture projects when we were in Seattle.

I ripped down some pine sub-flooring that came from the local French Big Box (Leroy Merlin), cut the edges at a 45, ripped the board in half, and glued/screwed them to a section of 1/2-ish (13mm) plywood. Exterior water-based poly was added to both the back and front before it went up on my clay-block garage shop wall with 8 large anchors. For my first French Cleat accessory: I had three small cut-off sections left from a picture shelf wall I did in my home office that I tacked to section of scrap ply to hold my #5 1/4 Jack, #4 smoother, and a couple of block planes. I keep the rest of my planes in a chest, but I use these constantly and wanted to have them in reach. I was so happy with how it all tuned out that I started building all sort of other holders and organizers: ones for squares, chisel rolls, Mallets, cords, apron hooks, saw horses, clamps, Japanese saws, etc… I ringed the garage with a single cleat about 6′ up for all sorts of diabolical organization plans, then hung two more above the lathe so that I would have a place to suspend my lathe chisel rack that is currently in progress and for a spot light that shines down on projects as they are turning.

I will update and post as I add new stuff.

French Cleat 2014 (2)

French Cleat 2014 (3)

French Cleat 2014 (4)

French Cleat 2014 (5)

French Cleat 2014 (6)

Talley - French Cleat attachments 2014 (1)

Talley - French Cleat attachments 2014 (2)

Talley - French Cleat attachments 2014 (3)

Talley - French Cleat attachments 2014 (4)

Talley - French Cleat attachments 2014 (5)

Talley - French Cleat attachments 2014 (6)

Talley - French Cleat attachments 2014 (7)

Talley - French Cleat attachments 2014 (8)

Tools I brought with me from the old country…

/ Matt Talley / Leave a comment

When planning our move to Toulouse, I came to the realization that I would not be able to take my entire shop with me. I didn’t relish the idea of replacing all my power tools and saws with 220vt/60Hz versions, only to have to sell them in a couple of years when we move back to Seattle. I decided that I would bring mostly my hand tools and and spend some quality time working small projects, cutting dovetails, tuning my planes, etc… There were three 24″X24″ boxes and one wooden chest full of edge moulding planes, Stanley Bench Planes, 4 rolls of chisels, mallets, Japanese saws, hand drills, dovetail tools, axes, draw knives, my half set (#2 – #18 even) of 1850ish Gleave hollows and rounds, squares, jigs, rasps, and assorted joinery paraphernalia.

My plan is to use the time here to do the detail work that I am usually in too much of a rush to even contemplate: carved scroll-work, mortised frames, insets, layered stain finishes, edging with the moulding planes, some light carving, maybe even cutting a few linen-fold panels. I have done a couple of little things already, but my first big task is to build a HEAVY work bench so that I will have a proper work space: I am going with a split top Neo-Roubo without a leg vise. I will be installing a cast iron Front Vise and a Screw Vise on the tail of the bench instead. No cabinets underneath so that I can store a shooting board and a Moxon vise. It WILL BE coming home to Seattle with us.

In the interest of full disclosure: I am not a neo-Luddite – I did buy an orbital sander right after we got here and I shipped my Ryobi 18vt tool set (circle saw, 2 drills, reciprocating saw, flashlight, & jig saw). The same sets are sold here and I got a 220vt charger that works with my existing batteries and picked up a couple of fresh new lithium-ion batteries in the process. Aside from the battery tools, I ordered a large wood lathe so that I can make furniture legs, tool handles, bowls, jar lids, platters, etc. I brought all my lathe chisels and chucks with me and I got a model that uses a DC motor that I can change over to one that runs on US current when we move back. It is much larger than my lathe in Seattle and will be a valuable addition to the shop there when we return.

Cutting trees down and making stuff

/ Matt Talley / 1 Comment

Shortly after we moved into La Maison du Talley, we cut 21 trees out of the backyard. There was only one serious tree – a 40′ cedar – and the rest were smaller Bay Laurels and Vine Maples that were blocking any possibility of sunlight reaching the ground. I kept some of the larger, straighter sections of the small trees and put them in the loft of the garage to dry and season, hoping that I would eventually make stuff out of them. That was three and a half years ago and while spring cleaning in the garage/shop this weekend I decided to take a little break and mess stuff up again 🙂 I pulled a couple of sections down and cut them to manageable size with the chop saw. I knew exactly what to do with pieces.

We have a neighbor who is crazy helpful and has a passion for dahlias. He grows and shares them with the whole street and has helped Stamps-With-Foot litter the edges of the yard and flower beds with them. She loaned him the bulb planter early this spring and he loved it. He had somehow gone through life as a gardener and just never tried one. I decided to make him his own with graduated depth gauge marks and a matching mallet to drive it into the odd patch of hard ground. The planter is made from a section of the vine maple and the mallet is turned from a hickory Little League baseball bat that I bought for $2.00 at Goodwill. The maple was super-dense and I counted 21 very tight growth rings on it. It grew in the shade under larger trees for all that time and that made it an especially hard and nice piece of wood to turn with sharp chisels – the wood shavings and tailings came off in long, thin, lace-like strips. An absolute pleasure to work with.

Since I was making sawdust already, I decided to keep going: The wife and I are planning to make some/most of our Christmas gifts this year. I have already started and added a few mallets for the woodworkers in my life (I am not spoiling the surprise – none of them read this blog…). I also turned a garden mallet for Stamp-With-Foot from a section of Laurel tree (her name-sake). I added the burned striped bands at her request after she saw her’s beside the others and got mallet-envy.

Just before my wife stomped out to the shop and MADE me come in for the night, I took a hunk of red oak that I have had for 10+ years and turned a couple of fancy door-stops. Since we live in a house built in 1928, the doors have a mind of their own and a well placed wedge keeps a person from walking into the edge of a door in the middle of the night. I will add some tung oil and a few coats of satin poly this week to finish them up.