Tools I brought with me from the old country…

When planning our move to Toulouse, I came to the realization that I would not be able to take my entire shop with me. I didn’t relish the idea of replacing all my power tools and saws with 220vt/60Hz versions, only to have to sell them in a couple of years when we move back to Seattle. I decided that I would bring mostly my hand tools and and spend some quality time working small projects, cutting dovetails, tuning my planes, etc… There were three 24″X24″ boxes and one wooden chest full of edge moulding planes, Stanley Bench Planes, 4 rolls of chisels, mallets, Japanese saws, hand drills, dovetail tools, axes, draw knives, my half set (#2 – #18 even) of 1850ish Gleave hollows and rounds, squares, jigs, rasps, and assorted joinery paraphernalia.

My plan is to use the time here to do the detail work that I am usually in too much of a rush to even contemplate: carved scroll-work, mortised frames, insets, layered stain finishes, edging with the moulding planes, some light carving, maybe even cutting a few linen-fold panels. I have done a couple of little things already, but my first big task is to build a HEAVY work bench so that I will have a proper work space: I am going with a split top Neo-Roubo without a leg vise. I will be installing a cast iron Front Vise and a Screw Vise on the tail of the bench instead. No cabinets underneath so that I can store a shooting board and a Moxon vise. It WILL BE coming home to Seattle with us.

In the interest of full disclosure: I am not a neo-Luddite – I did buy an orbital sander right after we got here and I shipped my Ryobi 18vt tool set (circle saw, 2 drills, reciprocating saw, flashlight, & jig saw). The same sets are sold here and I got a 220vt charger that works with my existing batteries and picked up a couple of fresh new lithium-ion batteries in the process. Aside from the battery tools, I ordered a large wood lathe so that I can make furniture legs, tool handles, bowls, jar lids, platters, etc. I brought all my lathe chisels and chucks with me and I got a model that uses a DC motor that I can change over to one that runs on US current when we move back. It is much larger than my lathe in Seattle and will be a valuable addition to the shop there when we return.

Left Out in the Rain

Stamps-With-Foot and I worked furiously in the warm sunshine on Sunday in our yard and on the final bits of the kitchen cabinets that needed to be done. Our last tasks for the day were building cabinet drawers and priming the two base cabinets. I had my ubiquitous notebook out, to the side of where we were working, checking off tasks and referring to measurements & notes as we went. We cleaned up the tools and paint around 6:30, changed, had dinner at a local Thai place and ventured out to our new Trader Joe’s for a little grocery shopping.

I was getting ready this morning for a trip to Boeing and started looking for my notebook because I needed a phone number in it. It then hit me like a baseball bat… My notebook… got left outside… overnight!… in the Rain!! FVCK!!!! I popped out the back door like my butt was on fire, my bathrobe flapping and losing a flip-flop in the dash. Damn… It was sitting on the side of the wheel barrow and had swollen to an inch thick. I walked back to the house, with my head hung down and blotted off what water I could and checked the pages – a light of hope. I use a waterproof, indelible ink in my fountain pens, so there was only a little loss of information or smeared blotches (in spots where I used a cheap pen) where detailed notes and drawings used to be. I could have been SO MUCH worse.

While most folks would have to live with a swollen book, most folks don’t have an awesome steel and iron 1920’s book press sitting in their home office… I blotted the pages again as best I could, separated the wettest ones with wax paper sheets, and put it in the press with cardboard and a towel plotter to get out as much water as possible. I left it there for 8 hours or so and removed it before the pages started to stick together. I then carefully opened every page, sat it on its end with the covers far apart, pages fanned open, on the kitchen tile floor in front of the heater vent. Everything should be just fine… I say that with hope in my heart and my fingers crossed.

I will let it dry for a day or two and then press it again for another 24 hours or so. I might take the opportunity to press a design or my name into the cover – I update when it come out of the press.

UPDATE 4-22-12: Took the notebook out of the press and it is nice and flat. While waiting for it finish pressing I made an embossing stamp out of a scrap piece of popular. My carving chisels were taken in a recent theft, so I used a dremel tool with the diamond carver bit to scratch a simple test piece. It is a stylized version of the Arabic word IQRA. I have more or less adopted it as my own hallmark and use it to stamp my furniture, cabinets, it is on my stationary, and I have a smaller version that I use as a wax seal here and there. I decided it was fine time to mark my notebooks as well.