Chopping Block Kitchen Island – IKEA Hack

Stamps-With_Foot has wanted a chopping block island for years. Our kitchen in Seattle just didn’t have the room for one, but the kitchen in France was PLENTY big enough. I looked into taking some 5/4 maple and gluing it up for her, but without a table saw and a power planer it would have been REALLY difficult. We found a couple that were already built, but they were between 400 and 900 Euros. No.Thank.You. After some deliberation, I decided on an IKEA island – the Groland. Stop Laughing and put down the stones…

While my son (The Ruminator) was here in France on his summer vacation, we bought one in a box, strapped it to the top of the car, drug it home, and started putting it together. I couldn’t leave it stock though, that is just not how I operate 🙂 We added a few flourishes to make it “better.”

1. Turned the legs on the lathe to give it bun feet
2. Glued it all together and added some extra dowels for reinforcement
3. Removed the steel rods on the original and plugged the holes with Dowels
4. Painted the base with a Sea Green Milk Paint
5. Added an additional block section to the bottom of the top panel – to make it super-solid
6. Cut a 6″ hole in the top for sweeping scraps off the work surface
7. Put a large plastic bin – removable from both sides – under scrap hole
8. Bolted rolling pin to one side to towels and placed 2 brass hooks on the other side
9. Scrapped the wood lattice bottom panel and used 7/8″ tongue and groove clear pine decking boards instead.
10. Polyurethaned the top – 5 coats – and bottom shelf so they match and make the painted base “pop”
11. Took a hunk of cherry tree trunk and turned it down as a lid for the scrap hole.

My Son and I had it installed just in time for my chef Father-in-Law, The Chatty Buddha, to visit and whip up a few fine meals using it as a work platform

Kitchen Island France 2014 (1)

Kitchen Island France 2014 (2)

Kitchen Island France 2014 (3)

Kitchen Island France 2014 (4)

Kitchen Island pieces 2014 (1)

Kitchen Island pieces 2014 (3)

Kitchen Island pieces 2014 (2)

Found Trunk

Last spring (2013), I was at the West Seattle Fruit Market and asked if I could snag an oak pallet that was sticking out of their dumpster. “No worries. Sure. Take whatever.” When I pulled out the pallet, I found an old trunk/chest under it that had the top ripped off and was in sad shape. I almost left it where it was, but then decided it would be good for tool storage in the shop as the top was under the box and all the pieces were there. I drug it all home and after I cleaned some old lettuce and a rotten beet out, stuck the thing under a wing of the table saw where it promptly started collecting sawdust.

While working on my own version of the Anarchist’s Tool Chest a few months later, I decided to fix the found trunk up as well. It took maybe a total of 2 hours was strait forward:

Vacuum job
Removal of the old bent and broken hardware
old hinges from some other scavenged project installed
Top refitted and put on
a little glue was applied to some trim
1″X4″ slats to reinforce the bottom…
A few well-placed screws
From the pieces of left-over pallet wood found on the same day, I glued up some 5″ blocks and turned them down to make bun feet.
Installation of the new feet
a quick light all-over sanding
Two coats of Teak tinted tung oil.
….and done…

Stamps-With-Foot saw it up on saw horses in the yard and claimed it for the house. Apparently, it was too “rustic & French & crafty” to be vanquished to warrens of my dark little shop to be abused with tools, dirt, dust, grease and boyness. When I first started putting it back together, I found stained receipt from a outdoor store (no date) and a cub scout pin wedged in the bottom. I surmised that this was a young man’s camping/scouting trunk that he or his dad or both built it together. From the construction and the materials used, it looks like it was put made in the late ’40’s or early 1950’s. It now sits in our living room in the south of France and serves as a coffee table and blanket/hammock storage chest.

A Few Turns of the Lathe

After our house was packed up and loaded on a container-ship bound for the Panama Canal and on to the Port of Marseilles, the only tool I had were my lathe chisels, so I made use of the time and spun out a few odds and ends: a few cord pull handles for the florescent lights in the basement. two jar lids for Stamps-With -Foot, a wooden pestle (2 actually) for kitchen herb grinding and a short honey dipper for her as well.

From the same section of wood as the pestles, I turned some small bun feet for Brodie’s new  food & water bowl stand.  I re-turned my ash carving mallet to change the handle profile and add some ring details.  As I was in the mallet mood, I made general use wood working mallet for my brother-in-law out of a Baseball Bat and reused the bat’s pommel and turned it into a foot massage nubbin for my wife.  I got points in the ledger for to wife-specific items.  Always a good thing.